Answer (1 of 7): Of course. Quite a standard procedure. We call it crusher dust, or manufactured sand. Dependent on the source rock and type of crusher, the particle shape is unlikely to be nice round grains, which makes for concrete that is not quite as nice to play with, but it is still far fr...

Marble powder: The marble dust is obtained from RAK ceramics. The specific gravity of tile dust is found to be 2.62 and the fineness is found to be 7.5%. 3.METHODOLOGY: The evaluation of tile powder which is used as a replacement of cement material begins with the concrete testing.

Hence result increased by the value of 9.2% and for 10% replacement with shows that marble powder when mixed with sand and cement sand the flexure strength also got increased about 9.3% but it together has low compressive strength as compared to the decreased when the mix contains 20% marble powder dust replacement of marble waste in cement and ...

Partial Replacement of Cement with Marble Dust Powder. : In this project we have made fly ash cement bricks with variations in its percentage of composition. The project describes the use of local fly ash in construction industry in a way to minimize the industrial waste. The aim of this project is to find that percentage of composition by ...

material which is partial replacement of cement with marble powder and sand with glass powder. In this concrete 10% of glass powder is commonly replaced by sand in optimum level and 0%, 10% & 20% of marble powder replaced with cement respectively. …

to partial replacement of the fine aggregate with marble powder. M25 of concrete mix has been taken and casted into cubes and astrength tests have been conducted. In this paper I conduct an experiment on partial replacement of sand with marble dust powder at different % of mdp which are 20,25,30,35,40%.

The use of marble dust as sand replacement enhances the tensile strength of concrete compared to that of control mix where as the tensile strength increases with increase of marble dust content up to 15% as seen in Fig. 17. Generally, the 10.0% marble dust content as sand replacement is considered the optimum content that achieving the highest ...

But the split tensile strength decreased for the mix which contains 20 % marble powder dust against cement (10%) and sand (10%) by 11%. Hence result shows that marble powder when mixed with sand and cement together has low split strength as compared to the replacement of marble waste in cement and sand individually. 3.3 Durability.

The research focuses on the effect of using waste marble powder and quarry dust as partial sand replacement materials on concrete properties. Massive exploitation of the nonrenewable natural resources to fulfill the aggregate requirement of billions

It was proved that the behavior of concrete produced from marble powder found that WMP as sand substitute improved concrete properties when compared to that as cement replacement [21].

4. Using marble powder and silica fume up to 20% as an additive materials enhancement the compressive strength up to 31.85%. 5. Based on the experiment result it showed that replacement of cement and sand by marble powder and silica fume we can replace up to the 20% of cement replacement. References

river sand. Quarry dust and Marble powder contains similar properties as that of river sand and hence accepted as a building material. The present paper focuses on investigating maximum percentage replacement of river sand by Quarry dust and Marble powder in varying equal percentages 0%, 10%, 20%, 30%, 40%, 50%, and 60% for M25 mix designations.

The durability as well as workability has increased to large extent by use of marble dust as replacement of fine aggregate and coarse aggregate. The effect on properties of concrete were investigated and concluded that optimum percentage for replacement of sand with …

20% marble powder dust as partial replacement of cement and sand together and also MX3 with 15% marble powder as partial replacement of sand, MX4 with 15% marble powder dust as partial replacement of cement and MX6 with 30% marble powder dust as partial replacement of cement and sand together. S.No. Characterist ics Specified value as per IS ...

Feb 04, 2020 For sand replacement, and by replacing 10% of sand with marble powder in (NF10), the compressive strength value rises up to 5% above the control CM. Replacing 5% of cement and 10% of sand with marble waste powder in NC5 + NF10 mix gives almost the same compressive strength value obtained from CM

QUANTITY OF MARBLE POWDER; 5% of cement replaced by marble powder = 377.38gm 10% of marble powder = 754.7 gm 15% of marble powder = 1.13 kg 20 %of marble powder = 1.5094 kg. Experimental conditions: Compressive strength of concrete was undertaken on 15 cm cubic specimens. at 7 days and 28 days of age.

Marble Powder (MP) The addition of Marble Powder as a partial replacement for Portland cement is highly beneficial on large-scale works due to versatile advantages of Marble dust powder. The marble powder obtained Appl. Sci. 2018, 8, 364 4 of 20 by the processing of marble serves as a waste material.

Influence of limestone waste as partial replacement material for sand and marble powder in concrete properties Omar M. Omar a, Ghada D. Abd Elhameed b,*, Mohamed A. Sherif a, Hassan A. Mohamadien c a Department of Civil Construction and Architecture, Faculty of Industrial Education, Suez, Egypt b Building Materials Research and Quality Control Institute, Housing and Building National Research ...

The percentage replacement of cement by metakaolin considered in this experimental study are 0, 2, 4, 6 and 8% by weight of cement and sand by marble powder are 20, 15, 10, 5 and 0%.

Marble powder is a micro-fine filler; due to this filler effect, concrete strength is enhanced. ... The effect of replacement of sand by marble waste and scoria on the cost of concrete, which is expressed by cost per cubic meter of concrete, is assessed based on the material prices collected from most common sources and suppliers.

0.5 =weight of water/1.472 weight of water=736 ml On the other hand, we need to calculate amount of marble powder by replacing with cement for 5% of marble powder we get the weight as =1.472x.05 =73.6 gms weight of cement required =1.472-73.6 =1.398 Kg amount of coarse aggregate and fine aggregate was similar as previous calculations

4) Rohit kumar use of marble powder as partial replacement of concrete in concrete mixing" ISSN: 2347-4718 sep. 2016 5) P.Bhuvaneshwari An partial replacement of cement by with waste marble powder in -8163 Apr.2015 6) D.suji experimental study on …

For sand replacement, and by replacing 10% of sand with marble powder in (NF10), the compressive strength value rises up to 5% above the control CM. Replacing 5% of cement and 10% of sand with marble waste powder in NC5 + NF10 mix gives almost the same compressive strength value obtained from CM.

The use of marble powder and green sand as fine aggregate replacement created a favorable effect on reducing the porosity of the concrete. The reduction in the water absorption caused a decrease in the voids and is responsible for the improvement in the mechanical strength and impermeability properties of concrete.

Aliabdo et al. (2014) reported that, the replacement of sand by 15% of marble powder is better for concrete strength than replacing cement. Ahmed O. Mashaly et al. (2016) found that replacing of a ...

river sand. Quarry dust and Marble powder contains similar properties as that of river sand and hence accepted as a building material. The present paper focuses on investigating maximum percentage replacement of river sand by Quarry dust and Marble powder in varying equal percentages 0%, 10%, 20%, 30%, 40%, 50%, and 60% for M25 mix designations.

percentages of marble powder 5 CONCLUSIONS From the test result the following conclusion can be drawn: a) The compressive strength of concrete is increased when the 5% of fine aggregate (sand) is partially replaced with marble powder and by further increasing the percentage of marble powder the compressive strength gradually de-creases.

Abstract-The present study is aimed at utilizing Waste marble powder and quarry sand as partial replacement of cement and fine aggregate in concrete and comparing it with conventional concrete. This experimental investigation is carried out in three phases in 1st phase M20 grade of concrete is produced

marble powder as a partial replacement in the cement and sand mix, where MX0 is control mix with no marble powder, MX1 with 10% marble powder as partial replacement of sand, MX2 with 10% marble powder as partial replacement of cement and MX3 with 15% marble powder as partial

Marble Powder As A Partial Replacement Of Sand. V. CONCLUSION From the test results it is clearly evident that granite powder as a partial replacement of sand proves to be beneficial when Durability properties of Concrete is considered. Durability of Concrete using Granite Fines is almost same as that of reference mix (GF0), However at 30% ...

75% replacement from sand with marble powder as additive. by percent 5, 10, and 15% by cement weight. Phase II, the. above experiment is repeated with the same components but.

Investigation on Partial Replacement of Cement with Marble Dust Powder on C-25 Concrete . The property test for cement, marble dust powder, sand and coarse aggregates were te56sted. Beside the physical property test, marble dust …